Electronic Injection Mold Common Faults and Maintenance Methods
In the production of the electronics industry, injection mold is the core tool for the production of precision electronic parts. Due to the high temperature, high pressure, and high-frequency use in the production process, electronic injection molds will face a variety of failures and losses in the process of use. Timely identification and resolution of mold failures, and effective maintenance, not only to extend the mold life but also to ensure product quality and production efficiency.
Common Types of Failures in Electronic Injection Molds
Product Raw Edge (Flying Edge)
Raw edges are excess material that spills out of the product at the parting surfaces of the mold, resulting in uneven edges of the part. Causes of burrs may include poor mold closure, damaged parting surfaces, or insufficient mold closing pressure. Raw edges can affect the appearance and assembly accuracy of electronic products.
Mold Wear
Molds are prone to wear and tear after long-term use, especially during high-pressure injection molding, resulting in a decrease in mold surface roughness. This situation is mostly seen in the slider, guide pillar, cavity, and other components. Wear will affect the surface quality and dimensional accuracy of the finished product.
Broken or Stuck Ejector Pins
The ejector pin is a key component that helps molded parts to be released from the mold. Due to frequent high-pressure operations, ejector pins can break or seize. This problem is usually caused by inadequate lubrication of the mold, long or thin ejector pins, or poor mold design.
Clogged Cooling System
The cooling system is used to regulate the mold temperature and maintain a stable molding cycle. However, after a long period of use, scale or impurities may accumulate in the cooling channels, causing clogging and affecting the cooling efficiency of the mold, which can lead to warping, deformation or dimensional instability of the finished product.
Mold Surface Corrosion
Due to the frequent exposure of molds to high temperatures and humid environments, coupled with the use of cooling water, the surface of the mold is susceptible to moisture and rust. Rusting will lead to rough surface of the finished product and even affect the quality of injection molding, resulting in early damage to the mold.
Maintenance Methods for Electronic Injection Molds
Regular Inspection and Cleaning
Regularly inspect each key part of the mold, especially the parting surface, ejector pin, slide and cavity surface. Use special cleaners and soft cloths to remove dirt and grease from the surfaces to ensure that the mold surfaces are smooth and clean. In addition, clean the cooling waterway regularly to prevent scale buildup leading to clogging and to ensure the operation of the cooling system.
Lubrication Maintenance
Moving parts such as ejector pins, sliders, and guide columns are easily worn out during frequent operations and must regularly be coated with lubricating oil. Use a special high-temperature lubricant and clean the surface of the parts thoroughly before lubrication to avoid dust and impurities mixing in and affecting the lubrication effect. Proper lubrication reduces the wear and tear of the parts and improves the smoothness of the mold operation and mold release effect.
Anti-corrosion Treatment
Molds should be treated against rust during non-working hours, especially in humid environments. After cleaning the surface of the mold, anti-rust oil can be sprayed to protect the mold. For molds that have not been used for a long time, they should be stored in a dry, ventilated place and covered with a dust cloth or moisture-proof material to avoid rusting from moisture.
Cooling System Maintenance
The channels of the cooling system are prone to scale accumulation or clogging, which affects the cooling efficiency. Regularly use a descaler to clean the cooling water channel to keep the water flow unimpeded. For molds that have been in use for a long time, consider installing a water filter to reduce the impact of impurities on the cooling system. Ensuring that the cooling system is unobstructed will help to maintain the temperature stability of the mold and prolong the service life of the mold.
Regular Inspection and Replacement of Ejector Pins
Ejector pins are subject to high pressure during the demolding process and are prone to deformation or breakage. Regularly check the condition of ejector pins and replace worn or deformed pins in time. Ensure the accuracy of the length and position of the ejector pin, so as not to affect the demolding effect and avoid problems such as jamming. Also, check the ejector holes and sliding parts, keep them clean and lubricated to ensure smooth movement of the ejector.
Preheating and Reasonable Use of the Mold
Before using the mold, proper preheating is recommended to reduce the damage of temperature shock to the mold. Molds should be used according to their design loads and material limitations to avoid exceeding the designed injection pressure, temperature or molding cycle. Proper use of the mold can reduce the frequency of failure and extend the working life of the mold.
Regular Inspection of Mold Dimensions and Accuracy
Mold dimensions and accuracy may change after a long period of use. Regularly inspect the critical dimensions and accuracy of the mold through CMM or other precision inspection equipment. Finding problems and timely adjustment or repair, to ensure that the mold always meets the production requirements, to avoid substandard precision affects the quality of finished products.
Factory Overview
Latest Post
The Importance of Injection Mold Temperature Control and Common Methods
How to Optimize the Cooling System of Injection Mold?
How Electronic Injection Molds Meet the Needs of Complex Structures?
Analysis of the Process of Injection Molding of Electronic Products
The Importance of Electronic Injection Mold in the Modern Manufacturing Industry
Influence of Injection Molding of Electronic Products on Material Selection
Call
+86-0769-86066062
info@kehuimold.com
Service Time
9:00 AM – 10:00 PM





